diff --git a/drivers/usb/misc/usb251xb.c b/drivers/usb/misc/usb251xb.c
index 11ec78e..9c8f7e2 100644
--- a/drivers/usb/misc/usb251xb.c
+++ b/drivers/usb/misc/usb251xb.c
@@ -20,12 +20,11 @@
  */
 
 #include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/module.h>
 #include <linux/nls.h>
 #include <linux/of_device.h>
-#include <linux/of_gpio.h>
 #include <linux/slab.h>
 
 /* Internal Register Set Addresses & Default Values acc. to DS00001692C */
@@ -126,7 +125,7 @@
 	struct device *dev;
 	struct i2c_client *i2c;
 	u8 skip_config;
-	int gpio_reset;
+	struct gpio_desc *gpio_reset;
 	u16 vendor_id;
 	u16 product_id;
 	u16 device_id;
@@ -234,13 +233,13 @@
 
 static void usb251xb_reset(struct usb251xb *hub, int state)
 {
-	if (!gpio_is_valid(hub->gpio_reset))
+	if (!hub->gpio_reset)
 		return;
 
-	gpio_set_value_cansleep(hub->gpio_reset, state);
+	gpiod_set_value_cansleep(hub->gpio_reset, state);
 
 	/* wait for hub recovery/stabilization */
-	if (state)
+	if (!state)
 		usleep_range(500, 750);	/* >=500us at power on */
 	else
 		usleep_range(1, 10);	/* >=1us at power down */
@@ -259,7 +258,7 @@
 		i2c_wb[0] = 0x01;
 		i2c_wb[1] = USB251XB_STATUS_COMMAND_ATTACH;
 
-		usb251xb_reset(hub, 1);
+		usb251xb_reset(hub, 0);
 
 		err = i2c_smbus_write_i2c_block_data(hub->i2c,
 				USB251XB_ADDR_STATUS_COMMAND, 2, i2c_wb);
@@ -309,7 +308,7 @@
 	i2c_wb[USB251XB_ADDR_PORT_MAP_7]        = hub->port_map7;
 	i2c_wb[USB251XB_ADDR_STATUS_COMMAND] = USB251XB_STATUS_COMMAND_ATTACH;
 
-	usb251xb_reset(hub, 1);
+	usb251xb_reset(hub, 0);
 
 	/* write registers */
 	for (i = 0; i < (USB251XB_I2C_REG_SZ / USB251XB_I2C_WRITE_SZ); i++) {
@@ -362,19 +361,13 @@
 	else
 		hub->skip_config = 0;
 
-	hub->gpio_reset = of_get_named_gpio(np, "reset-gpios", 0);
-	if (hub->gpio_reset == -EPROBE_DEFER)
+	hub->gpio_reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (PTR_ERR(hub->gpio_reset) == -EPROBE_DEFER) {
 		return -EPROBE_DEFER;
-	if (gpio_is_valid(hub->gpio_reset)) {
-		err = devm_gpio_request_one(dev, hub->gpio_reset,
-					    GPIOF_OUT_INIT_LOW,
-					    "usb251xb reset");
-		if (err) {
-			dev_err(dev,
-				"unable to request GPIO %d as reset pin (%d)\n",
-				hub->gpio_reset, err);
-			return err;
-		}
+	} else if (IS_ERR(hub->gpio_reset)) {
+		err = PTR_ERR(hub->gpio_reset);
+		dev_err(dev, "unable to request GPIO reset pin (%d)\n", err);
+		return err;
 	}
 
 	if (of_property_read_u16_array(np, "vendor-id", &hub->vendor_id, 1))