* Freescale i.MX8QM IOMUX Controller

Required properties:
- compatible: "fsl,imx8qm-iomuxc"
- fsl,pins: each entry consists of 2 integers. Its format is
  <pin_id pin_config>.

pin_config definition:
- i.MX8QM have different pad types, please refer to below pad
  register definitions, the pinctrl driver will just write the
  pin_config into the hardware register.

typedef union _hw_pad_iomux
{
    uint32_t U;
    struct _hw_pad_iomux_bitfields0
    {
        uint32_t GP : 19; /*!< [18:0] GP controls. */
        uint32_t WAKEUP : 3; /*!< [21:19] Wakeup controls. */
        uint32_t WAKEUP_ENB : 1; /*!< [22] Wakeup write enable. */
        uint32_t LPCONFIG : 2; /*!< [24:23] Low-power config. */
        uint32_t CONFIG : 2; /*!< [26:25] Config. */
        uint32_t IFMUX : 3; /*!< [29:27] Mux. */
        uint32_t GP_ENB : 1; /*!< [30] GP write enable. */
        uint32_t IFMUX_ENB : 1; /*!< [31] Mux write enable. */
    } B;
    struct _hw_pad_iomux_28fdsoi
    {
        uint32_t DSE : 3; /*!< [2:0] Drive strength. */
        uint32_t _reserved1 : 2; /*!< [4:3] */
        uint32_t PS : 2; /*!< [6:5] Pull select. */
        uint32_t _reserved2 : 12; /*!< [18:7] */
        uint32_t WAKEUP : 3; /*!< [21:19] Wakeup controls. */
        uint32_t WAKEUP_ENB : 1; /*!< [22] Wakeup write enable. */
        uint32_t LPCONFIG : 2; /*!< [24:23] Low-power config. */
        uint32_t CONFIG : 2; /*!< [26:25] Config. */
        uint32_t IFMUX : 3; /*!< [29:27] Mux. */
        uint32_t GP_ENB : 1; /*!< [30] GP write enable. */
        uint32_t IFMUX_ENB : 1; /*!< [31] Mux write enable. */
    } FDS0I28;
    struct _hw_pad_iomux_28fdsoi_hsic
    {
        uint32_t DSE : 3; /*!< [2:0] Drive strength. */
        uint32_t HYS : 1; /*!< [3] Hysteresis. */
        uint32_t PUS : 2; /*!< [5:4] Pull-up select. */
        uint32_t PKE : 1; /*!< [6] Pad keeper enable. */
        uint32_t PUE : 1; /*!< [7] Pull-up enable. */
        uint32_t _reserved2 : 11; /*!< [18:8] */
        uint32_t WAKEUP : 3; /*!< [21:19] Wakeup controls. */
        uint32_t WAKEUP_ENB : 1; /*!< [22] Wakeup write enable. */
        uint32_t LPCONFIG : 2; /*!< [24:23] Low-power config. */
        uint32_t CONFIG : 2; /*!< [26:25] Config. */
        uint32_t IFMUX : 3; /*!< [29:27] Mux. */
        uint32_t GP_ENB : 1; /*!< [30] GP write enable. */
        uint32_t IFMUX_ENB : 1; /*!< [31] Mux write enable. */
    } FDS0I28_HSIC;
    struct _hw_pad_iomux_28fdsoi_comp
    {
        uint32_t COMPEN : 3; /*!< [2:0] Mode. */
        uint32_t FASTFRZ : 1; /*!< [3] Fast freeze. */
        uint32_t PSW_OVR  : 1; /*!< [4] 2.5 volt override */
        uint32_t RASRCP : 4; /*!< [8:5] PMOS comp. */
        uint32_t RASRCN : 4; /*!< [12:9] NMOS comp. */
        uint32_t NASRC_SEL : 1; /*!< [13] Read NASRC select. */
        uint32_t COMPOK  : 1; /*!< [14] Comp status. */
        uint32_t NASRC : 4; /*!< [18:15] NASRC value. */
        uint32_t _reserved2 : 4; /*!< [22:19] */
        uint32_t LPCONFIG : 2; /*!< [24:23] Low-power config. */
        uint32_t _reserved3 : 5; /*!< [29:25] */
        uint32_t GP_ENB : 1; /*!< [30] GP write enable. */
        uint32_t IFMUX_ENB : 1; /*!< [31] Mux write enable. */
    } FDS0I28_COMP;
} hw_pad_iomux_t;