| # Originally NVRAM file for BCM943341WLAGB_2 P203 board | |
| # For Murata 1BW | |
| manfid=0x2d0 | |
| prodid=0x0653 | |
| vendid=0x14e4 | |
| devid=0x4386 | |
| boardtype=0x0653 | |
| boardrev=0x1203 | |
| boardnum=22 | |
| macaddr=00:90:4c:c5:12:38 | |
| sromrev=3 | |
| boardflags=0x0080201 | |
| xtalfreq=37400 | |
| nocrc=1 | |
| ag0=255 | |
| aa2g=1 | |
| ccode=ALL | |
| #PA parameters for 2.4GHz | |
| pa0b0=6706 | |
| pa0b1=-814 | |
| pa0b2=-191 | |
| tssifloor2g=64 | |
| # rssi params for 2.4GHz | |
| rssismf2g=0xf | |
| rssismc2g=0x8 | |
| rssisav2g=0x1 | |
| cckPwrOffset=1 | |
| PwrOffset40mhz2g=8 | |
| # rssi params for 5GHz | |
| rssismf5g=0xf | |
| rssismc5g=0x7 | |
| #rssisav5g=0x1 | |
| rssisav5g=0x3 | |
| #PA parameters for lower a-band | |
| pa1lob0=5785 | |
| pa1lob1=-714 | |
| pa1lob2=-172 | |
| tssifloor5gl=32 | |
| #PA parameters for midband | |
| pa1b0=5880 | |
| pa1b1=-721 | |
| pa1b2=-174 | |
| tssifloor5gm=34 | |
| #PA paramasdeters for high band | |
| pa1hib0=6206 | |
| pa1hib1=-722 | |
| pa1hib2=-147 | |
| tssifloor5gh=32 | |
| rxpo5g=0 | |
| maxp2ga0=0x4c | |
| # 19dBm board limit; 18dBm target | |
| #Per rate power back-offs for g band, in .5 dB steps. Set it once you have the right numbers. | |
| cck2gpo=0x2222 | |
| # R6~54 13 dBm | |
| ofdm2gpo=0xaaaaaaaa | |
| # M0~M3 16 dBm board limit; 15 dBm target | |
| mcs2gpo0=0xcccc | |
| # M7 16dBm; M6 16 dBm; M5 16 dBm; M4 16 dBm board limit; 15 dBm target | |
| mcs2gpo1=0xcccc | |
| # max power for 5G 15 dBm | |
| maxp5ga0=0x3c | |
| # 15 dBm board limit; 14 dBm target | |
| maxp5gla0=0x3c | |
| maxp5gha0=0x3c | |
| #Per rate power back-offs for a band, in .5 dB steps. Set it once you have the right numbers. | |
| ofdm5gpo=0x22222222 | |
| # R54 15dBm; R48 15 dBm; R6~R36 15 dBm board limit; 14 dBm target | |
| ofdm5glpo=0x22222222 | |
| ofdm5ghpo=0x22222222 | |
| mcs5gpo0=0x4444 | |
| # M0~M4 15dBm max ; 14 dBm target | |
| mcs5gpo1=0x4444 | |
| # M7 15 dBm; M6 15 dBm; M5 15 dBm board limit; 14 dBm target | |
| mcs5glpo0=0x4444 | |
| mcs5glpo1=0x4444 | |
| mcs5ghpo0=0x4444 | |
| mcs5ghpo1=0x0000 | |
| swctrlmap_2g=0x00080008,0x00100010,0x00080008,0x011010,0x11f | |
| #swctrlmap_5g=0x00020002,0x00040004,0x00020002,0x011010,0x2fe | |
| ## For GN04100 | |
| swctrlmap_5g=0x00040004,0x00020002,0x00040004,0x011010,0x2fe | |
| gain=32 | |
| triso2g=8 | |
| triso5g=8 | |
| #tx parameters | |
| loflag=0 | |
| iqlocalidx5g=40 | |
| dlocalidx5g=70 | |
| iqcalidx5g=50 | |
| lpbckmode5g=1 | |
| txiqlopapu5g=0 | |
| txiqlopapu2g=0 | |
| dlorange_lowlimit=5 | |
| txalpfbyp=1 | |
| txalpfpu=1 | |
| dacrate2xen=1 | |
| papden2g=1 | |
| papden5g=1 | |
| #rx parameters | |
| gain_settle_dly_2g=4 | |
| gain_settle_dly_5g=4 | |
| noise_cal_po_2g=-1 | |
| noise_cal_po_40_2g=-1 | |
| noise_cal_high_gain_2g=73 | |
| noise_cal_nf_substract_val_2g=346 | |
| noise_cal_po_5g=-1 | |
| noise_cal_po_40_5g=-1 | |
| noise_cal_high_gain_5g=73 | |
| noise_cal_nf_substract_val_5g=346 | |
| cckpapden=1 | |
| aci_detect_en_2g=1 | |
| interference=3 | |
| # OOB IRQ settings -- comment out next 4 "sd" parameters for SDIO In-Band | |
| #sd_gpout=0 | |
| #sd_oobonly=1 | |
| #sd_gpval=1 | |
| #sd_gpdc=0 | |
| Comment out HW_OOB setting -- not used for 1BW | |
| #mux_enab=0x11 |