| # This file allows user to override the factory |
| |
| # defaults for the WLAN Driver |
| |
| #Host module debug |
| vosTraceEnableHDD=0 |
| vosTraceEnableWDA=0 |
| vosTraceEnableWDI=0 |
| vosTraceEnableSME=0 |
| vosTraceEnablePE=0 |
| vosTraceEnableWMA=0 |
| vosTraceEnableVOSS=0 |
| gEnableLogp=1 |
| |
| #Prioritize user(hostapd, iw,) specified country |
| gCountryCodePriority=1 |
| |
| #Host logging |
| gMulticastHostFwMsgs=0 |
| |
| #packetlog |
| gEnablePacketLog=0 |
| |
| #Enable firmware uart print |
| gEnablefwprint=0 |
| |
| #Enable firmware log |
| gEnablefwlog=0 |
| |
| # Disable FW log function by default |
| gFwDebugLogType=0 |
| gFwDebugModuleLoglevel=0,0 |
| |
| # Generic |
| |
| # Phy Mode (auto, b, g, n, etc) |
| # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only |
| # 7 = 11b only 8 = 11ac only. |
| gDot11Mode=0 |
| |
| # VHT Tx/Rx MCS values |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gVhtRxMCS=2 |
| gVhtTxMCS=2 |
| |
| # VHT Tx/Rx MCS values for 2x2 |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gEnable2x2=1 |
| gVhtRxMCS2x2=2 |
| gVhtTxMCS2x2=2 |
| |
| gVhtChannelWidth=2 |
| |
| #Short Guard Interval Enable/disable |
| gShortGI20Mhz=1 |
| gShortGI40Mhz=1 |
| |
| #Channel Bonding |
| gChannelBondingMode5GHz=1 |
| |
| # 1=enable STBC; 0=disable STBC |
| gEnableRXSTBC=1 |
| |
| # 1=enable tx STBC; 0=disable |
| gEnableTXSTBC=1 |
| |
| # 1=enable rx LDPC; 0=disable |
| gEnableRXLDPC=1 |
| |
| #If set to 0, MCC is not allowed. |
| gEnableMCCMode=1 |
| |
| # Enable or Disable MCC Adaptive Scheduler at the FW |
| # 1=Enable (default), 0=Disable |
| gEnableMCCAdaptiveScheduler=1 |
| |
| # Enable BMPS or not |
| gEnableBmps=1 |
| |
| # Enable IMPS or not |
| gEnableImps=1 |
| |
| # Enable/Disable Idle Scan |
| gEnableIdleScan=0 |
| |
| #Data Inactivity Timeout when in powersave (in ms) |
| gDataInactivityTimeout=200 |
| |
| # Increase sleep duration (seconds) during IMPS |
| # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
| # unnecessary if Idle Scan is disabled. |
| gImpsModSleepTime=0 |
| |
| # Enable suspend or not |
| # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| gEnableSuspend=3 |
| |
| |
| #Enable/Disable UAPSD for SoftAP |
| gEnableApUapsd=1 |
| |
| # UAPSD service interval for VO,VI, BE, BK traffic |
| InfraUapsdVoSrvIntv=0 |
| InfraUapsdViSrvIntv=0 |
| InfraUapsdBeSrvIntv=0 |
| InfraUapsdBkSrvIntv=0 |
| |
| # Flag to allow STA send AddTspec even when ACM is Off |
| gAddTSWhenACMIsOff=1 |
| |
| # Beacon filtering frequency (unit in beacon intervals) |
| gNthBeaconFilter=50 |
| |
| # Enable WAPI or not |
| WAPIIsEnabled=0 |
| # Flags to filter Mcast abd Bcast RX packets. |
| # Value 0: No filtering, 1: Filter all Multicast. |
| # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast |
| McastBcastFilter=3 |
| |
| #Flag to enable HostARPOffload feature or not |
| hostArpOffload=0 |
| |
| #Flag to enable TCPChkSumOffld feature or not |
| gEnableTCPChkSumOffld=0 |
| |
| #Flag to enable HostNSOffload feature or not |
| hostNSOffload=0 |
| |
| #Flag to enable IPChkSumOffld feature or not |
| gEnableIPChecksumOffload=0 |
| |
| # 802.11n Protection flag |
| gEnableApProt=1 |
| |
| #Enable OBSS protection |
| gEnableApOBSSProt=1 |
| |
| # Fixed Rate |
| gFixedRate=0 |
| |
| # RTS threshold |
| RTSThreshold=192000 |
| |
| # Intra-BSS forward |
| gDisableIntraBssFwd=0 |
| |
| # WMM Enable/Disable |
| WmmIsEnabled=0 |
| |
| # 802.11d support |
| g11dSupportEnabled=1 |
| |
| # 802.11h support |
| g11hSupportEnabled=1 |
| |
| # ESE Support and fast transition |
| EseEnabled=0 |
| ImplicitQosIsEnabled=0 |
| gNeighborScanTimerPeriod=200 |
| |
| gNeighborLookupThreshold=76 |
| gNeighborReassocThreshold=81 |
| |
| gNeighborScanChannelMinTime=20 |
| gNeighborScanChannelMaxTime=30 |
| gMaxNeighborReqTries=3 |
| |
| gEnableFastRoamInConcurrency=1 |
| |
| # CSR Roaming Enable(1) Disable(0) |
| gRoamingTime=0 |
| |
| # Roaming Preference |
| gRoamPrefer5GHz=1 |
| gSelect5GHzMargin=20 |
| |
| # Legacy (non-ESE, non-802.11r) Fast Roaming Support |
| # To enable, set FastRoamEnabled=1 |
| # To disable, set FastRoamEnabled=0 |
| FastRoamEnabled=1 |
| |
| #Check if the AP to which we are roaming is better than current AP in terms of RSSI. |
| #Checking is disabled if set to Zero.Otherwise it will use this value as to how better |
| #the RSSI of the new/roamable AP should be for roaming |
| RoamRssiDiff=3 |
| |
| # If the RSSI of any available candidate is better than currently associated |
| # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without |
| # registering for reassoc threshold). |
| # NOTE: Value of 0 means that we would register for reassoc threshold. |
| gImmediateRoamRssiDiff=10 |
| |
| # To enable, set gRoamIntraBand=1 (Roaming within band) |
| # To disable, set gRoamIntraBand=0 (Roaming across band) |
| gRoamIntraBand=0 |
| |
| # SAP Country code |
| # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| # Example |
| # US Indoor, USI |
| # Korea Outdoor, KRO |
| # Japan without optional byte, JP |
| # France without optional byte, FR |
| #gAPCntryCode=US |
| |
| #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| gAPAutoShutOff=0 |
| |
| # SAP auto channel selection configuration |
| # 0 = disable auto channel selection |
| # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| gApAutoChannelSelection=0 |
| |
| #Preferred band (both or 2.4 only or 5 only) |
| BandCapability=0 |
| |
| #Beacon Early Termination (1 = enable the BET feature, 0 = disable) |
| enableBeaconEarlyTermination=0 |
| beaconEarlyTerminationWakeInterval=3 |
| |
| #SOFTAP Channel Range selection |
| gAPChannelSelectStartChannel=1 |
| gAPChannelSelectEndChannel=11 |
| |
| #SOFTAP Channel Range selection Operating band |
| # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND |
| gAPChannelSelectOperatingBand=0 |
| |
| # Listen Energy Detect Mode Configuration |
| # Valid values 0-128 |
| # 128 means disable Energy Detect feature |
| # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. |
| # 10-128 are reserved. |
| # The EDET threshold mapping is as follows in 3dB step: |
| # 0 = -60 dBm |
| # 1 = -63 dBm |
| # 2 = -66 dBm |
| # ... |
| # 7 = -81 dBm |
| # 8 = -84 dBm |
| # 9 = -87 dBm |
| |
| # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: |
| |
| # |
| # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. |
| # |
| gEnablePhyAgcListenMode=128 |
| |
| #Enable Keep alive with non-zero period value |
| gStaKeepAlivePeriod = 30 |
| #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). |
| #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) |
| #For both active and power save clients. |
| |
| #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. |
| #If doesn't honor for 5 seconds then DUT remove client. |
| |
| #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on |
| #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. |
| #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. |
| |
| #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period |
| #where we send NULL frame. |
| gApLinkMonitorPeriod = 10 |
| gGoLinkMonitorPeriod = 10 |
| |
| #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. |
| #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. |
| gGoKeepAlivePeriod = 20 |
| gApKeepAlivePeriod = 20 |
| |
| #If set will start with active scan after driver load, otherwise will start with |
| #passive scan to find out the domain |
| gEnableBypass11d=1 |
| |
| #If set to 0, will not scan DFS channels |
| gEnableDFSChnlScan=1 |
| |
| # Enable Automatic Tx Power control |
| gEnableAutomaticTxPowerControl=1 |
| |
| # 0 for OLPC 1 for CLPC and SCPC |
| gEnableCloseLoop=1 |
| |
| # Scan Timing Parameters |
| gPassiveMaxChannelTime=110 |
| gPassiveMinChannelTime=60 |
| gActiveMaxChannelTime=40 |
| gActiveMinChannelTime=20 |
| |
| # Enable Active mode offload |
| gEnableActiveModeOffload=1 |
| |
| #Enable Scan Results Aging based on timer |
| #Timer value is in seconds |
| #If Set to 0 it will not enable the feature |
| gScanAgingTime=0 |
| |
| #Enable Power saving mechanism Based on Android Framework |
| #If set to 0 Driver internally control the Power saving mechanism |
| #If set to 1 Android Framwrok control the Power saving mechanism |
| isAndroidPsEn=0 |
| |
| #disable LDPC in STA mode if the AP is TXBF capable |
| gDisableLDPCWithTxbfAP=0 |
| |
| #Enable thermal mitigation |
| gThermalMitigationEnable=1 |
| gThermalTempMinLevel1=90 |
| gThermalTempMaxLevel0=110 |
| gThermalTempMaxLevel1=115 |
| gThrottlePeriod=100 |
| |
| #List of Country codes for which 11ac needs to be disabled |
| #Each country code must be delimited by comma(,) |
| gListOfNon11acCountryCode=RU,UA,ZA |
| |
| #Maxium Channel time in msec |
| gMaxMediumTime = 6000 |
| |
| #FlexConnect Power Factor |
| #Default is set to 0 (disable) |
| gFlexConnectPowerFactor=0 |
| |
| #Disable split scan, the FW will take care of it |
| gNumChanCombinedConc=60 |
| |
| #Enable Power Save offload |
| gEnablePowerSaveOffload=1 |
| |
| gEnableWoW=1 |
| |
| #Enable or Disable p2p device address administered |
| isP2pDeviceAddrAdministrated=0 |
| |
| #Disable scan_pno by default |
| gPNOScanSupport=0 |
| |
| #Enable TDLS |
| gEnableTDLSSupport=1 |
| |
| # Regulatory Setting; 0=STRICT; 1=CUSTOM |
| gRegulatoryChangeCountry=1 |
| |
| # Enable or Disable Rx thread |
| # 1=Enable (default), 0=Disable |
| gEnableRxThread=0 |
| |
| # Enable or Disable FW self-recovery |
| # Currently, It's for USB only. |
| # 1=Enable, 0=Disable (default) |
| gEnableFwSelfRecovery=0 |
| gEnableSelfRecovery=0 |
| gEnableForceTargetAssert=0 |
| # Enable or Disable SAP suspend |
| # 1=Enable (default), 0=Disable |
| gEnableSapSuspend=0 |
| |
| # Enable TxBF |
| gTxBFEnable=1 |
| |
| # Enable or Disable WOW Pulse feature |
| # 1 = Enable, 0 = Disable (default) |
| gwow_pulse_support = 0 |
| |
| #P2P Listen offload |
| gEnableP2pListenOffload=1 |
| |
| # gEnableSAPAuthOffload: Enable Software AP Authentication Offload feature |
| # 1=Enable, 0=Disable (default) |
| gEnableSAPAuthOffload=0 |
| |
| # Sifs burst feature configuration |
| gEnableSifsBurst=1 |
| gSoftApMaxPeers=10 |
| |
| gVhtMpduLen=2 |
| # FW reorder |
| gReorderOffloadSupported=1 |
| # DFS Master Capability |
| gEnableDFSMasterCap=1 |
| |
| #Fine tuned TxFlow parameters |
| TxFlowLowWaterMark=300 |
| TxFlowHighWaterMarkOffset=94 |
| |
| # PTA |
| gCoexPtaConfigEnable=0 |
| gCoexPtaConfigParam=0 |
| gEnableNanSupport=0 |
| |
| #ETSI |
| gStaLocalEDCAForETSI=0 |
| #TxBF in 20MHz |
| gEnableTxBFin20MHz=1 |
| END |
| # Note: Configuration parser would not read anything past the END marker |
